Instructions
For optimal results, we recommend using a heat press with all our transfers. While an iron can be used, for the best application and longest durability, we strongly advise using a heat press. As all heat presses are different, please understand these instructions are a guideline only. We assume no responsibility for damage to your garment or transfers during the application process.
Washing instructions: Wash in cold water delicate cycle inside out, dry on low. Do not use bleach, bleach alternative or fabric softener
Below you will find instructions for application of our heat transfer materials.
Pre-press garments for 10 seconds prior to application
Suitable fabrics: cotton, polyester, spandex, blends
DTF (Direct to Film)
Heat Press Instructions:
1. Place image up on garment, cap, or bag
2. Press at 300F for 8 seconds with heavy pressure.
3. Peel film off when cold
4. Cover with teflon or parchment paper and repress at 300F for 8 seconds
Iron-On Instructions:
1. Prepare your fabric: Make sure your fabric is clean and dry. Iron it to remove any wrinkles.
2. Position the transfer: Place the DTF transfer face down on your fabric, aligning it where you want it.
3. Cover the transfer: Place a sheet of parchment paper or Teflon sheet over the transfer. This will protect the transfer and your iron.
4. Set your iron: Set your iron to the highest heat setting (usually cotton setting) and turn off the steam function.
Apply heat and pressure: Press the iron firmly onto the parchment paper for 20-30 seconds, moving the iron in a circular motion to ensure even heat distribution.
Let it cool: Allow the transfer to cool completely before removing the parchment paper.
5. Peel the film: Gently peel off the clear film from the transfer when cool
Spangles
Heat Press Instructions:
1. Remove the white backing from the transfer.
2.. Place the transfer sticky side down (image up) onto the fabric.
3. It is now ready to press with your heat press machine : 300 F medium pressure 10 seconds
4. Peel hot at an angel and hold down garment while peeling. If the spangles did not stick, simply lay the transfer back down and re-press.
Iron-on Instructions:
1. Remove the white backing from the transfer.
2. Place the transfer sticky side down onto the fabric (image up).
3. Set the iron to the medium setting.
5. You want to iron on a hard flat surface (not a padded ironing board). Place a thin pressing cloth over the design. Apply pressure only with NO STEAM by placing the iron directly on top of the design and holding it in place for 20 seconds. For larger designs, you will have to do this in sections.
6. Wait for the transfer tape to cool but still remain a little warm to the touch then slowly remove it. If any of the spangle remain on the tape, simply lay it back down and iron over those stones.
7. Once the transfer tape is removed, turn the garment inside out and iron the design following the instructions above. This helps pull the adhesive into the fabric.
Rhinestones
Heat Press Instructions
1. Remove the white backing from the transfer.
2. Check to make sure no stones have moved out of place. If any have moved simply put them back in place with a pair of tweezers.
3. Place the transfer sticky side down onto the fabric. You may want to use a thin pressing cloth between fabrics layers to prevent the adhesive from gluing the layers together.
4. It is now ready to press with your heat press machine : 325F light to medium pressure 15 seconds
5. Let the transfer cool till it is warm to the touch then slowly peel off the plastic tape. If the stones did not stick, simply lay the transfer back down and re-press.
Iron On Instructions
1. Remove the white backing from the transfer.
2. Check to make sure no stones have moved out of place. If any have moved simply put them back in place with a pair of tweezers.
3. Place the transfer sticky side down onto the fabric. You may want to use a thin pressing cloth between fabrics layers to prevent the adhesive from gluing the layers together.
4. Set the iron to the highest possible setting for your fabric (the wool or cotton setting is the most desirable).
5. You want to iron on a hard flat surface (not a padded ironing board). Place a thin pressing cloth over the design. Apply pressure only with NO STEAM by placing the iron directly on top of the design and holding it in place for 20-30 seconds. For larger designs, you will have to do this in sections.
6. Wait for the transfer tape to cool but still remain a little warm to the touch then slowly remove it. If any of the stones remain on the tape, simply lay it back down and iron over those stones.
7. Once the transfer tape is removed, turn the garment inside out and iron the design following the instructions above. This helps pull the adhesive into the fabric.
Patches
Some of our patches will come with a clear removable backing that will need to be removed prior to application. We will let you know if there is a backing
Heat Press Instructions:
We also recommend using a heat pillow under the garment to ensure the best pressure.
1. To apply , position image up on shirt
2. Cover with a teflon sheet, press 20 sec at 325F moderate pressure.
3. Turn shirt inside out and repress
Iron-on Instructions
1. Lay your shirt on a flat, heat-resistant surface like an ironing board. Position the patch where you want it on the shirt.
2. Set your iron to the highest heat setting without steam.
3. Iron the patch: Press down firmly on the iron for about 15-20 seconds. Apply even pressure to ensure good adhesion.
4. Flip the shirt: Turn the shirt inside out.
Iron the back: Place the cotton cloth over the patch again and iron the back of the patch for an additional 10-15 seconds. This will help secure the adhesive.
5. Let it cool: Allow the patch to cool completely before wearing the shirt.